How to Set Up Your Pool Cleaner Robot for Optimal Performance？

Properly installing your robot pool cleaner is the best way to make sure your new cleaner works its best right from day one. Whether you are replacing a traditional pool vacuum or leaving such worst pool vacuum nightmare as a manual skimmer, or even worse than that “might have shimmer” (that’s another name for a vacuum cleaner for pool), a well-prepared installation will help you with the pool maintenance and provide a efficient pool vacuum cleaner.

In this guide we’ll take you through the fundamental steps to get your swimming pool robot cleaner up and running for long-term success.

Select an Appropriate Position to Supply Your Power

The Determination of placement of power supply unit is the very first part to install this pool in ground Pool cleaner unit. It should be placed:

At least 10 feet away from the water of the pool.
In a cool and dry place without the direct exposure to sunlight or any other source of heat to avoid burning or electrical damage.
Close enough to be able to reach the pool with the robot’s power cable without strain.
Only 1m away Recharge Cord:Do not wrap the cable too tightly when using the pool cleaner, as users of many pool cleaning robots have had problems with the cable tangling.

Prep the Pool for Cleaning

Prepare Your Pool Before Using Your Pool Cleaning Robot The pool before you begin writing your pool cleaning robot. Here’s how:

If necessary manually skim the larger debris with a skimmer.
Stash pool toys, solar covers, and obstructions elsewhere.
Review water chemistry — properly balanced levels leads to more effective filtration.
And if there is a lot of buildup or biofilm present, you might want to learn how to acid wash pool surfaces before using the robot.
Preppin’ your pool Preparing your home pool well is one way to ensure that your robot cleaner can run well without getting stuck.

Place and Submerge the Robot

Now ease the robot pool cleaner down into the pool. Don’t throw it, it may hurt fragile sensors. Let it sink of its own weight, tipping it slightly to allow air bubbles to escape.

Wait for it to sink to the bottom of the pool before beginning to clean.

The Cleaning Settings Matters It may sound so simple, but everything is just down to the right settings for cleaning.

Commercial cleaners do so, especially Beatbot AquaSense 2 Ultra, Beatbot AquaSense 2 Pro, and Beatbot AquaSense 2. These may include:

Floor only
Floor and wall
Full coverage with waterline

Use full-cycle settings for deep cleans, or during periods of heavy use. And these are intelligent alternatives to a traditional pool vacuum robot or traditional vacuum for pool.

Never Use a Naughty Filter Again Clean Filter After Every Application

Said filter basket or canister collects everything from leaves and sand to fine debris. After each cleaning cycle:

Open the access panel and remove filter.
Rinse thoroughly with a hose.
Check for damage or buildup.

If the filter isn’t cleaned often, it can start to underperform, especially on algae. For difficult cases, learn how to vacuum an algae infested pool.

Turn on Wall Clinging Abilities (When Possible)

If you have a wall climbing pool cleaner make sure you have feature checked in your settings. Note: Some robots can auto change mode, while some cannot, But if you have questions about trying to change mode, just reply this mail directly, we will be very glad to help you!

SPECIAL FEATURES: Tired of your robot pool cleaner getting stuck on main drains and other difficult loose floor surfaces or on your steps?

Guard Response & Third Set In New Definition, to Change the Side of Return, Then Adjust On Performance.

The earliest cycles are the most crucial for assessing how your robot is faring. Keep an eye out for:

Missed spots or corners.
Debris rich areas.
Problems such as the robot floating or becoming stuck.
Adjust if necessary and see your owner’s manual. (Many units now have smartphone apps for real-time monitoring.)
Clear Up Installation Confusion: Booster Pumps and Drains

There are still some pool owners who ask, what is a pool booster pum or how to drain an inground pool without a pump. In the majority of robotic units, at least (and especially with smart, self-contained units like Beatbot and Maytronics pool cleaner systems), you won’t require any additional plumbing.

Robotic units run separately from your pool’s filtration, saving energy and extending equipment life.

Final Thoughts: Get it right = Get it (this powerful) right!

That does the job of the outdated cleaning system better than any manual pool vacuum is installed correctly and put to preferred use. Whether you’re employing a simple cleaner or high-tech one such as Beatbot, setting up your system with care establishes the path to great cleanup.

With regular use and proper care, your pool robot will help keep your water pristine, minimize algae build-up, and cut down the time and effort it takes to maintain your swimming pool all season long.